Applying velocity envelope to slip clip

SeldomSeen wrote on 11/17/2022, 2:37 PM

I hope this makes sense?! I have a 5 clip and have made a split at 1 minute. I want to then apply a velocity envelope to that 1 minute only. When I do it applies it to the whole 5 minutes so i can't use those black triangles to trim it down to avoid it repeating so i can sink it up after the 1 minute clip? Cheers. (Vegas 20)

Comments

john_dennis wrote on 11/17/2022, 5:25 PM

@SeldomSeen

Watch this epic.

My main system:
Motherboard: Asus X99-AII
CPU: Intel i7-6850K
GPU: Sapphire Radeon RX480-8GB
RAM: Corsair Dominator (4 x 4 GB) DDR4 2400
Disk O/S & Programs: Intel SSD 750 (400 GB)
Disk Active Projects: 1TB & 2TB WD BLACK SN750 NVMe Internal PCI Express 3.0 x4 Solid State Drives
Disk Other: WD Ultrastar/Hitachi Hard Drives: WDBBUR0080BNC-WRSN, HGST HUH728080ALE600, 724040ALE640, HDS3020BLA642
Case: LIAN LI PC-90 Black Aluminum ATX Full Tower Case
CPU cooling: Corsair Hydro series H115i
Power supply: SeaSonic SS-750KM3 750W 80 PLUS GOLD Certified Full Modular Active PFC Power Supply
Drive Bay: Kingwin KF-256-BK 2.5" and 3.5" Trayless Hot Swap Rack with USB 3
Sound card: Crystal Sound 3 on motherboard. Recording done on another system.
Primary Monitor: Asus ProArt PA248q (24" 1920 x 1200)
O/S: Windows 10 Pro 22H2, Build 19045.2130

Camera: Sony RX10 Model IV

https://www.youtube.com/user/thedennischannel

SeldomSeen wrote on 11/18/2022, 4:21 AM

I've done a quick screen record hoping to make it a little clearer! What I want to do is only add velocity to the split clip, then be able to split it again (as I usually do using that black triangle thing), thus syncing it back up to the next bit? But it is using the full length off the video to end the velocity section with the black triangle.

Thanks again!

Dexcon wrote on 11/18/2022, 4:54 AM

I'm not sure why there is a need to split the video event to apply a velocity change. Why not apply the velocity envelope to the entire video event and use nodes (double click at the desired point on the velocity line) to change the velocity rate.

In the above, the velocity rate is 100%, then 0%, then 200%, then 300%, then back to 100% - and no notches created. R clicking on a node opens a context window providing velocity rate selections and includes a manually selectable % velocity rate:

I'm not sure what you mean by "syncing" (which usually refers to audio/video alignment???) - the uploaded video does not that make clear.

Cameras: Sony FDR-AX100E; GoPro Hero 11 Black Creator Edition

Installed: Vegas Pro 16 Edit, Vegas Pro 17 Edit, Vegas Pro 18, Vegas Pro 19 Edit, Vegas Pro 20 Edit, HitFilm Pro 2021.3, BCC 2023, Mocha Pro 2022.5.1, Ignite Pro, NBFX TotalFX 7, Neat NR, DVD Architect 6.0, MAGIX Travel Maps, Sound Forge Pro 16, SpectraLayers Pro 9, iZotope RX10 Advanced and many other iZ plugins, Vegasaur 4.0

Windows 11

Dell Alienware Aurora 11

10th Gen Intel i9 10900KF - 10 cores (20 threads) - 3.7 to 5.3 GHz

NVIDIA GeForce RTX 2080 SUPER 8GB GDDR6 - liquid cooled

64GB RAM - Dual Channel HyperX FURY DDR4 XMP at 3200MHz

C drive: 1TB M.2 PCIe NVMe SSD

D drive: 6TB WD 7200 rpm Black HDD 3.5"

E & F drives: 2 x 2TB Barracuda HDDs 2.5"

 

Joelson wrote on 11/18/2022, 5:18 AM

@SeldomSeen I understand what you want.

1.Select the event where you will apply the velocity envelope.
2.Right click and choose Create Subclip
3.Again right mouse button / Switch / Trim events to include all frames
4.After that apply velocity envelope

Dexcon wrote on 11/18/2022, 5:55 AM

Notwithstanding, I have several times in the last few months using Vegas Pro 20 (and over the years in other VP versions using a number of earlier computers) been able to split a video event after one frame, 0% freeze that one frame and then stretch it out to, say, 2 seconds and then butt it up to the 100% continuation of that same video event after the split point - all without the need to create a subclip and without the frozen velocity event affecting the following 100% continuation of the same video event after the split point, and without creating the end of event notch (black triangle???). I do this to create a freeze frame at the beginning of the video event mostly to cover a dissolve and then release it to 100% velocity at the split point.

Sorry to say but the 2 uploaded video examples have not illuminated my understanding of what is being done as they are without a commentary - jiggling the curser over a later video event unfortunately explains nothing for me.

Cameras: Sony FDR-AX100E; GoPro Hero 11 Black Creator Edition

Installed: Vegas Pro 16 Edit, Vegas Pro 17 Edit, Vegas Pro 18, Vegas Pro 19 Edit, Vegas Pro 20 Edit, HitFilm Pro 2021.3, BCC 2023, Mocha Pro 2022.5.1, Ignite Pro, NBFX TotalFX 7, Neat NR, DVD Architect 6.0, MAGIX Travel Maps, Sound Forge Pro 16, SpectraLayers Pro 9, iZotope RX10 Advanced and many other iZ plugins, Vegasaur 4.0

Windows 11

Dell Alienware Aurora 11

10th Gen Intel i9 10900KF - 10 cores (20 threads) - 3.7 to 5.3 GHz

NVIDIA GeForce RTX 2080 SUPER 8GB GDDR6 - liquid cooled

64GB RAM - Dual Channel HyperX FURY DDR4 XMP at 3200MHz

C drive: 1TB M.2 PCIe NVMe SSD

D drive: 6TB WD 7200 rpm Black HDD 3.5"

E & F drives: 2 x 2TB Barracuda HDDs 2.5"

 

FayFen wrote on 11/18/2022, 6:08 AM

On my VP19 I set after I split (which should be the proper default, I never understood this loop or hold last frame thing), so on high velocity the clip will be trimmed and not looped